Waterproof Universal Off Road Relay and Fuse Power Distribution Center

Description

Welcome to BP Automotive.
Home
About us
Returns
Shipping Policy
Contact Us
Feedback
Add to Favorite Seller
Join Mailing List
CATEGORIES
Home
Standalone Harnesses
LS and LT Swap Accessories
Accessories and Harness Parts
New Arrivals
Clearance
Same Day Shipping
100% Satisfaction Guaranteed
30 Days Money Back Guarantee
Product information
Waterproof Universal Off Road Relay and Fuse Power Distribution Center
Click on the Image to Enlarge
Description:
Waterproof Universal Off Road Fuse and Relay Power Distribution Center
Application
Any 12VDC Vehicle with added accessories that are too much draw for the vehicles factory power distribution system. Accessories such as an air ride compressor, lights, audio equipment, and fans. These are just a few examples; the opportunities are limitless.
THIS IS NOT FOR REWORKING AN LS HARNESS!
Description
Our Waterproof Universal Power Distribution Center is made of the highest quality materials. Cooper Bussman manufactures the fuse block, and we use genuine Aptiv (Formerly Delphi) terminals and seals to populate the Power Distribution Center. We also provide high quality connectors and Aptiv (Formerly Delphi) heat shrink to make your connections to the fuse block! We guarantee you will love the heat shrink, as there is nothing better on the market! There is 3 foot of wire for power and ground and 8 foot of wire for the relay controls, relay outputs, and fused outputs providing plenty of mounting options! There are 5 fused relay circuits and 5 fuse only circuits!
Cooper Bussman rates the max working load of this fuse block at
80 amp
.
The Unit is 3.5 x 7 inches and 4.5 inches tall.
1 - Main Power Supply - 8ga TXL Wire
3 Foot Long!
1 - Relay Coil Ground - 14ga TXL Wire
3 Foot Long!
5 - Relay Controls - 18ga TXL Wire
8 Foot Long!
5 - Relay Outputs - 12ga TXL Wire
8 Foot Long!
5 - Fuse Outputs - 16ga TXL Wire
8 Foot Long!
5 - 35 Amp Normally Open Relays
All needed fuses
Extra Fuses
OEM Aptiv (Formerly Delphi) Heat Shrink (This is the
GOOD
stuff!)
Uninsulated butt connectors for a good crimp and great connection when soldered after crimping!
Why BP Automotive?
All of the wire included in our products is TXL wire that meets or exceed OEM standards! This high temperature wire has maximum chemical resistance as well.
Beware of many companies that use primary wire that has a much lower heat and abrasion tolerance and will not last against chemicals and heat. TXL wire is far superior in every way, don’t settle for less. We supply the same materials that are found in OEM vehicles, not parts stores, especially when it comes to the wire-that the coating will melt when the wire is soldered!
We have also included stainless socket head bolts to hold the mounting brackets for a rust free, long lasting good look!
Additional Info
This Power Distribution Center will require some knowledge to install and use it. It is wired for an easy install and includes a diagram so that you can wire it to your application. Due to the universal nature of this item it is impossible to provide exact diagrams for your applications! However, the universal nature of this item really makes your install options limitless!
Why BP Automotive?
All of the wire included in our products is TXL wire that meets or exceed OEM standards! This high temperature wire has maximum chemical resistance as well. Beware of many companies that use primary wire that has a much lower heat tolerance and will not last against chemicals. TXL wire is far superior in every way, don’t settle for less. We supply the same materials that are found in OEM vehicles, not parts stores, especially when it comes to the wire-that the coating will melt when the wire is soldered!
BP Automotive uses Rennsteig production hand tools and production presses that meet Delphi crimp height and crimp width standards. This is where most of our competitors differ from us. Many of them use Dephi repair tools that are only meant for repair use, and the crimp is supposed to be soldered once complete. This doesn’t work out well, especially if they are using primary wire and not TXL wire. With the Rennsteig production hand tools you get a perfect, solder-less crimp every time!
Shipping
BP Automotive generally ships the same business day for any items that are in stock if your order is placed
before 2pm Central Standard Time
. Our system emails tracking information when we ship your order. It is important to check your junk mail folder as it sometimes will land in your Junk or Spam folder. All eBay orders have tracking automatically updated and can be tracked from the time of shipment via your “My Ebay” purchases page.
All orders shipped through the eBay Global Shipping Program will need to be tracked only through your “My Ebay” purchases page, as once your order reaches their shipping hub in Erlanger, Kentucky our system will send you an Item Delivered email.
This email only confirms that it has been delivered to the Ebay Global Shipping Center. You must finish tracking it the rest of the way via your “My Ebay” purchases page.
Please be aware of all national holidays, as most shipping carriers are closed on many national holidays and this may prevent your item from shipping the same or the next business day depending on the date and time purchased. Ebay will give you an estimated time of delivery once you purchase the item, this
usually
has any holidays factored in.
BP Automotive only ships to the address that eBay provides to us as the shipping address
.
No exceptions.
Any item that is returned as not deliverable will not be shipped out again until the customer pays for shipping it back again. Please ensure that the address in your eBay account is correct to ensure that there aren’t any delays or extra fees incurred before receiving your item.
Returns
BP Automotive will accept returns for uninstalled items only.  No exceptions.  Any item that has been installed may be exchanged for the same item only if the item is defective.  BP Automotive reserves the right to inspect all items before a replacement is sent back out.  It is the buyer’s responsibility to send the item back to BP Automotive, and if the item is truly defective BP Automotive will reimburse the amount of shipping to send the item back to BP Automotive and send a replacement item back.
In the event that you are wanting to return an uninstalled item BP Automotive will accept your return under the following circumstances-
Item or items are uninstalled.
The item is in new condition.
The item being returned has been purchased in the past 30 days.
If the original packaging is damaged the return will be subject to a restocking fee no matter the timeframe of your return. Minimum of 10%.
Restocking fees are calculated by the timeframe from which your order was placed.  The restocking fees are as follows-
0-10 days 15%
10-20 days 15%
20-30 days 20%
All return shipping fees are to be paid by the buyer.  All returns must be preapproved by BP Automotive and the RMA number must be clearly visible on the outside of the box.  The original invoice and RMA number must also be provided inside the box.  This must be done to ensure that your return is approved and that there are not any delays in processing your return.
About us
With decades of GM Fuel Injection experience, you can rely on BP Automotive to provide you with the highest quality fuel injection products possible. All of our products are hand built at our facility in Columbia, Kentucky. You can count on the attention to detail and the quality that “Made in the USA“ brings to mind when purchasing our products!
Our experience and attention to detail has enabled us to build standalone and direct fit GM fuel injection harnesses that are unsurpassed in quality and longevity. We offer a lifetime warranty on all of our products, which is 5 years or 100,000 miles-whichever comes first. This is as good or better than the warranty you will get with a brand-new vehicle! We achieve this confidence in our product by using the most up to date manufacturing methods and materials that are approved by the SAE and USCAR panels.
At the very foundation of our harnesses we utilize TXL (Cross-Linked Thin Wall) SAE J1128 wire. This is the very same wire used in factory automobile harnesses. When a splice is made for the harness, we utilize splices that are Sonically Welded together, just like a harness for a factory vehicle. This welds the copper core from all wires together to create one solid splice of copper. Then we cover the splice with OEM grade Aptiv (formerly Delphi) heat shrink, not just some aftermarket adhesive heat shrink. The heat shrink we use adds support and superior resistance to chemicals and weather.
When we assemble a harness, we utilize GM color codes for our harness. If the GM diagrams call for a Green/White stripe wire that is what we use-not just a dark green wire. Many of our competitors are only using solid color wire and advertising that they are using GM color codes, we use even striped wire here at BP Automotive! We also follow GM wire sizing specs from the diagrams as well, so there aren’t any under or over sized wires in our harnesses!
When it comes to terminating a connection in an automotive fuel injection harness there are many standards and considerations that you must take to ensure that you are truly building a harness to GM, SAE, or USCAR standards. At BP Automotive we utilize production crimp tooling, some of which we had special made to ensure that we can crimp terminals to these standards. After a crimp is made with the tooling we use it is checked with a special digital dial caliper to ensure it meets crimp height and width standards. The tolerances for these standards are as small as a .10 or .01 of a MM! You can have confidence that when you purchase a harness from BP Automotive that you won’t have bad connections from crimps made with the repair tooling that many of our competitors are using.
We use all original connectors, terminals, and seals when we build harnesses. These are components made by OEM suppliers like Aptiv (formerly Delphi), TE Connectivity, Kostal, and Molex. BP Automotive does not use knock off PRC (People’s Republic of China) made connectors, terminals, and seals that you see many harnesses made from that have recently surfaced on the market. We only use OEM connectors on our harnesses, we will never sacrifice quality to save a few pennies.
We cover all of our harnesses in OEM grade loom to ensure that the harness has the protection it needs to last and stand the test of time! With both of the looms that we use you can rest assured that not only is your harness protected, but that it also looks great! All circuits that are ran by a heat source, like the oxygen sensors are covered in a 1200-degree fiberglass braid that adds even more protection! Lastly, we install a high quality Aptiv grommet so that in the event you decide to mount the controller in the passenger compartment you can seal your firewall and have a clean, professional looking installation!
For the final stage of production, we test each harness with our computer harness tester to ensure that the harness doesn’t have any broken wires or mis wired connections. This ensures that when you get your harness it is perfect! You can purchase from BP Automotive with confidence knowing that when you get your harness it will work and will continue to work for years to come!
Join Our Exclusive Newsletter For Up To Date News, Special Offers And New Arrivals
Sign up Now
Shop Categories
Standalone Harnesses
LS and LT Swap Accessories
Accessories and Harness Parts
New Arrivals
Clearance
Quick Links
Feedback
Add to Favorite Seller
Shop info
Home
About us
Returns
Delivery
Contact Us
Get in touch with us
BP Automotive
5220 Liberty Rd
Columbia, KY 42728-9017
United States
Payment info
Copyright 2018
BP Automotive.
All Rights Reserved
Listing and template services provided by inkFrog